A.X. Home Pro is loading
White wooden door with a silver lever handle

Door Repairs: Sticking, Sagging and Not Latching

Posted by:

|

On:

|

Sticking: humidity swelling or loose hinges. Sagging: tighten or replace hinge screws with longer ones. Not latching: adjust the strike plate. Doors get used dozens of times a day, so even a small problem becomes a daily annoyance. A door that sticks, scrapes the floor or won’t stay closed isn’t just irritating; it can wear out hardware, damage the door and frame and, on exterior doors, compromise security and let in drafts. Most door problems come down to a handful of causes, and many are fixable in minutes with a screwdriver. Here’s how to diagnose and fix the most common ones.

Start by Watching the Door

Before reaching for tools, open and close the door slowly and watch carefully.

  • Where does it rub? Look for worn paint or shiny spots on the door edge or frame.
  • Is the gap between the door and the frame even along the top and the latch side?
  • Does the top corner on the latch side drag, or the bottom corner scrape the floor?
  • When the door closes, does the latch line up with the hole in the strike plate?
  • Grab the door’s handle side and lift gently. Do the hinges shift or move?

These clues tell you whether you’re dealing with swelling, loose hinges, a sagging door or a misaligned latch.

Advertisement

Sticking Doors

The two most common culprits are humidity swelling or loose hinges.

Humidity swelling

Wood absorbs moisture from the air and expands. In humid weather, a wooden door, or one with unsealed edges, can swell enough to rub against the frame. Doors in bathrooms, basements and exterior doors are especially prone to it. Often the door works fine in drier months and sticks in summer.

What to do:

  • Check whether the top and bottom edges are painted or sealed. Unsealed edges absorb moisture freely. Sealing all six sides of a wood door helps keep moisture levels stable.
  • Reduce indoor humidity with exhaust fans, air conditioning or a dehumidifier where needed.
  • If the door still rubs once humidity is under control, lightly plane or sand the high spot, then seal the bare wood. Remove only as much as needed; a door planed too much in humid weather may have a large gap once it dries out.

Loose hinges

Before planing anything, check the hinges. Loose hinge screws let a door shift so it rubs in one spot. Tighten every hinge screw on both the door and the frame. Very often, that alone solves the problem.

Sagging Doors

A sagging door usually drops at the latch side, so the top corner rubs the frame or the bottom drags on the floor. The cause is often the top hinge pulling away from the frame because the weight of the door works the screws loose over time.

Advertisement

The fix: tighten or replace hinge screws with longer ones

  1. Tighten all hinge screws first. If they snug up and the door straightens, you’re done.
  2. If screws spin without tightening, the holes are stripped.
  3. Replace one or more top hinge screws with longer ones. Original hinge screws are often short and only reach into the door jamb. A longer screw, driven through the hinge and the jamb into the framing stud behind it, holds much more firmly and pulls the door back up into position. Choose screws that match the head size and finish of the hinge.
  4. For stripped holes in the door itself, one common approach is to fill the hole with wood glue and wooden toothpicks or a small dowel, let it dry, trim it flush and re-drive the screw.

Driving a longer screw into the top hinge on the jamb side can also be used to make small adjustments, pulling the door slightly toward the hinge side to open up a tight gap on the latch side.

Doors That Won’t Latch

When a door closes but won’t latch, the latch bolt isn’t lining up with the opening in the strike plate on the frame. The fix is to adjust the strike plate.

Find the misalignment

Rub a little lipstick, chalk or a dry-erase marker on the end of the latch bolt, then close the door gently. The mark on the strike plate shows exactly where the bolt is hitting compared with the opening.

Adjust the strike plate

  • Slight misalignment: Remove the strike plate and use a file to enlarge the opening slightly in the direction needed.
  • Larger misalignment: Move the strike plate up or down. This usually means deepening the mortise in the frame with a chisel, filling the old screw holes and reattaching the plate.
  • Door too far from the strike: Some strike plates have an adjustable tab. If the door rattles when closed, bending the tab slightly can create a snug fit.

Before adjusting the strike, check the hinges. A latching problem is often caused by a door that’s sagging, and fixing the hinges can bring the latch back into line.

Other Common Door Problems

  • Squeaky hinges: Remove one hinge pin at a time, clean it and apply a light lubricant before reinstalling.
  • Door swings open or closed on its own: The door may be out of plumb. Hinge adjustments or a slight bend to a hinge pin can help.
  • Drafts around exterior doors: Replace worn weather stripping and the door sweep.
  • Deadbolt that’s hard to turn: The bolt may not be lining up with its strike, often for the same reasons as a latch.

Common Mistakes

  • Planing first. Always check hinges before removing wood.
  • Forgetting to seal planed edges. Bare wood will absorb moisture and swell again.
  • Overtightening screws into soft wood, which strips the holes.
  • Ignoring frame problems. Large or changing gaps, or cracks in the walls around a door, may signal settling that’s worth a closer look.

What to Do This Week

  • Open and close every door slowly, noting rubbing, gaps and latching issues.
  • Tighten all hinge screws.
  • Replace stripped top hinge screws with longer ones into the stud.
  • Use the lipstick trick to adjust any strike plates that don’t line up.
  • Seal any unsealed door edges.

If a door needs planing, rehanging or replacement, or the frame itself needs repair, we can help. AX Home Pro handles repairs, improvements and maintenance for homeowners. Request an estimate to get started.

Latest stories

View all

Posted by

in

--:--·---·--°

Designed and Built by Fenway Web.

Our Network & Sponsors

Advertisement

Boston Made+Join Boston Made+$20/mo or $199/yr — save $41 when you pay annuallyJoin Now →Paxton-Digital

Advertisement

♫ Music Video Player
Press play — keeps playing while you browse