If you can feel a draft near your front door on a breezy day, you are paying to heat the outdoors. Weather stripping is the simple seal that keeps conditioned air in and outside air out, and it wears out more often than most homeowners realize. The fix is straightforward: replace compressed or cracked strips, and add door sweeps. It is one of the most affordable comfort upgrades you can make before winter.
Why Weather Stripping Wears Out
Weather stripping lives a hard life. Every time a door or window opens and closes, the seal gets squeezed, rubbed and flexed. Add sunlight, temperature swings, moisture and pets, and even good materials eventually give up. Common causes of failure include:
- Compression. Foam and rubber flatten over time and stop springing back to fill the gap.
- Cracking. Vinyl and rubber dry out and become brittle, especially on sunny exposures.
- Tearing. Strips catch on hardware, get chewed by pets or get damaged when furniture moves through a doorway.
- Adhesive failure. Peel-and-stick products lose their grip and fall away.
- House movement. Doors that sag or shift change the size of the gap the seal needs to fill.
How to Find Leaks
Check every exterior door, including the garage entry door and back door, plus operable windows and the attic hatch.
- Look for light. With the door closed, turn off the lights inside during daytime and look for daylight around the edges and threshold.
- Feel for air. On a windy day, run your hand slowly along the edges.
- Use smoke or flame. Hold a lit incense stick or candle near the edges and watch for flicker or drifting smoke. Keep flame away from curtains and anything flammable.
- Try the paper test. Close the door on a sheet of paper. If it slides out easily, the seal is not making good contact.
- Inspect the strips. Look for flattened, cracked, torn or missing sections.
Choosing Replacement Weather Stripping
Many types are available, and the best choice depends on where it goes and how the existing seal is attached.
For doors
- Kerf-in weather stripping. Many modern exterior doors have a groove, or kerf, in the frame. Replacement strips press right into that slot. Take a piece of the old strip with you to match the profile.
- Foam tape. Easy peel-and-stick option for irregular gaps; best where there is little friction.
- V-strip, or tension seal. A folded strip that springs open to seal the side of a door or window sash. Durable and nearly invisible.
- Tubular rubber or vinyl. Flexible bulb seals that conform to uneven gaps.
- Magnetic weather stripping. Common on steel doors, forming a tight seal similar to a refrigerator door.
For windows
- V-strip along sash channels on double-hung windows
- Foam or rubber tape along the bottom of the sash
- Replacement seals specific to the window manufacturer for many modern units
Add Door Sweeps
The gap at the bottom of an exterior door is often the biggest single source of drafts. Door sweeps close it.
- Screw-on sweeps mount to the inside face of the door with a rubber, vinyl or brush strip that drags lightly on the threshold.
- Slide-on or U-shaped door bottoms wrap around the bottom edge of the door.
- Adjustable thresholds on many exterior doors can be raised slightly with screws to meet the sweep.
- Automatic door bottoms drop down when the door closes and lift when it opens.
A good sweep seals the gap without making the door hard to close. If the door scrapes heavily or will not latch, adjust the sweep height or the threshold.
How to Replace Weather Stripping
- Remove the old strip. Pull kerf-in strips out of the groove, or peel off old foam and scrape away adhesive.
- Clean the surface. Wipe the frame with a mild cleaner and let it dry completely. Adhesive will not stick to dirt.
- Measure and cut. Measure each side and the head of the frame separately. Cut strips slightly long, then trim.
- Install. Press kerf-in strips firmly into the groove, or apply tape-style strips in a straight, continuous line.
- Mind the corners. Make tight, neat joints so there are no gaps where sides meet the head.
- Install the sweep. Close the door, position the sweep so it touches the threshold lightly, mark the screw holes and fasten it.
- Test. Open and close the door several times. Repeat the light or paper test to confirm the seal.
When the Problem Is Not the Weather Stripping
Sometimes new seals do not stop the draft because the door itself is the issue. Look for:
- Sagging doors that rub on one side and gap on the other. Tightening or replacing hinge screws with longer screws often helps.
- Strike plates that keep the door from closing firmly. Adjusting the strike can pull the door tighter to the seal.
- Warped doors that will not seal evenly no matter what.
- Gaps around the frame behind the trim, which need caulk or low-expansion foam.
- Rotted thresholds or frames that need repair.
What to Do This Week
- Check every exterior door and window for light, drafts and worn seals.
- Take a piece of old weather stripping to match the profile.
- Replace compressed or cracked strips.
- Add door sweeps or adjust thresholds where you see a gap at the bottom.
- Note doors that sag or will not latch tightly for repair.
AX Home Pro handles repairs, improvements and maintenance for homeowners. Request an estimate to get started.





