A.X. Home Pro is loading
Old metal gas cans hanging from wooden beams

Preparing the Lawn Equipment for Storage

Posted by:

|

On:

|

When the mowing season winds down, it is tempting to roll the mower into the shed and forget about it until spring. That is how carburetors get gummed up, blades rust and engines refuse to start on the first warm Saturday. A little care now pays off later, and the routine is short: drain or stabilize fuel, clean, sharpen blades, store dry. Here is how to handle each step for mowers, string trimmers, blowers and other outdoor power equipment, plus a few extras that keep everything ready to go when the grass starts growing again.

Start with safety. Before any maintenance, let the engine cool completely. For gas equipment, disconnect the spark plug wire so the engine cannot start accidentally while you are working near the blade. For battery equipment, remove the battery. Work on a flat surface in a well-ventilated area away from open flames and pilot lights, and wear gloves when handling blades. Always check your owner’s manual first, since manufacturers have specific recommendations for their equipment.

Step 1: Drain or Stabilize Fuel

Fuel is the biggest cause of hard starts after storage. Gasoline breaks down over time, and fuel blends containing ethanol can absorb moisture and leave gummy deposits that clog small carburetor passages. You have two good options:

Advertisement

Option A: Stabilize

  1. Add a fuel stabilizer to fresh fuel in the tank, following the product’s directions.
  2. Run the engine for several minutes so the treated fuel reaches the carburetor.
  3. Store with the tank nearly full, which leaves less room for moisture-laden air.

Option B: Drain

  1. Run the equipment until the tank is nearly empty, or carefully siphon out fuel into an approved container.
  2. Start and run the engine until it stops on its own to clear the carburetor.
  3. Dispose of or reuse old fuel properly; do not pour it on the ground or down a drain.

Which is better depends on your equipment and its manual. Two-stroke tools that run on mixed fuel have their own guidance. Whichever you choose, also treat or use up the fuel in your storage cans so you are not starting spring with stale gas.

Step 2: Clean

Grass clippings, dirt and sap trap moisture against metal and encourage rust and corrosion. A clean machine stores better and runs cooler.

  • Under the deck: With the spark plug disconnected, tip the mower as directed in the manual (usually with the air filter and carburetor side up to avoid leaks) and scrape caked grass from the underside. Some decks have a washout port for a hose.
  • Engine and cooling fins: Brush debris from around the engine so air can flow when it runs.
  • Air filter: Clean or replace it. A clogged filter makes the engine work harder.
  • Trimmers and blowers: Clear debris from the guard, head and intake screens.
  • Battery equipment: Wipe down the tool, check vents and clean battery contacts.

Step 3: Sharpen Blades

A sharp mower blade cuts grass cleanly; a dull one tears it, leaving ragged tips that brown and invite disease. Sharpening in fall means you start spring ready to mow.

  1. Mark the blade’s bottom side so it goes back on correctly.
  2. Remove it using a block of wood to keep the blade from turning while you loosen the bolt.
  3. Sharpen the cutting edges with a file or grinder, following the original angle. Take off only what is needed.
  4. Check balance by hanging the blade on a nail or balancer. If one side drops, remove a bit more from the heavy side.
  5. Replace blades that are bent, cracked or worn thin.
  6. Reinstall and tighten to the manufacturer’s specification.

Also check trimmer line, hedge trimmer blades and pruning tools. Clean and oil hand tools like shears and loppers so they do not rust over winter.

Step 4: Store Dry

Where and how you store equipment matters as much as preparing it.

Advertisement
  • Choose a dry, covered space like a garage or shed, away from water heaters, furnaces and other ignition sources if fuel remains in the tank.
  • Keep equipment off damp concrete when possible, using a pallet or shelf.
  • Use a breathable cover rather than a plastic tarp, which can trap condensation.
  • Store batteries indoors at moderate temperature, at the charge level the manufacturer recommends, rather than in a freezing shed.
  • Store fuel only in approved containers, clearly labeled.

Extra maintenance worth doing now

  • Oil: Many manufacturers recommend changing engine oil at the end of the season so used oil does not sit in the engine all winter.
  • Spark plug: Inspect and replace if worn or fouled.
  • Belts and cables: Look for cracks, fraying or slack on drive belts and throttle cables.
  • Tires: Check pressure on riding mowers and tractors.
  • Riding mower batteries: Keep charged with a maintainer during storage if recommended.

Common Mistakes to Avoid

  • Storing with untreated fuel in the tank.
  • Tipping a mower the wrong way and flooding the air filter with oil.
  • Working near the blade with the spark plug still connected.
  • Leaving wet clippings caked under the deck.
  • Storing lithium batteries in freezing temperatures.

What to Do This Weekend

  1. Decide whether to drain or stabilize fuel for each machine.
  2. Clean decks, engines, filters and tool heads.
  3. Sharpen or replace mower blades and clean hand tools.
  4. Change oil and inspect plugs, belts and cables.
  5. Store everything dry, covered and off the floor.

Need a better place to store it all? Shed repairs, garage shelving and wall storage are the kinds of projects we handle every day. AX Home Pro handles repairs, improvements and maintenance for homeowners. Request an estimate to get started.

Latest stories

View all

Posted by

in

--:--·---·--°

Designed and Built by Fenway Web.

Our Network & Sponsors

Advertisement

Boston Made+Join Boston Made+$20/mo or $199/yr — save $41 when you pay annuallyJoin Now →PupWear (.org)

Advertisement

♫ Music Video Player
Press play — keeps playing while you browse