A sump pump is the kind of equipment you forget about until the moment you need it most. It sits quietly in a pit in your basement or crawlspace, waiting for groundwater to rise, and then it works hard during heavy rains to keep water out of your home. If it fails during a storm, the damage can be significant. The good news is that checking it is simple. Pour water in the pit to confirm it runs, and consider a battery backup so it keeps working when the power goes out.
How a Sump Pump Works
A sump pump sits in a pit, called a sump basin, at the lowest point of a basement or crawlspace. Drain tile or perimeter drains around the foundation direct groundwater into that pit. When the water rises to a certain level, a float switch turns the pump on. The pump pushes the water up through a discharge pipe and out of the house, usually through a check valve that keeps water from flowing back into the pit. When the water level drops, the float lowers and the pump shuts off.
Most residential sump pumps are one of two types:
- Submersible pumps sit inside the pit, under water. They are quieter and often used in finished basements.
- Pedestal pumps have the motor mounted above the pit on a column, with only the intake down in the water. They are easier to service.
How to Check Your Sump Pump
Test your pump at least a few times a year, and especially before seasons of heavy rain or snowmelt. Early fall is a good time.
- Check the power. Make sure the pump is plugged in and the outlet has power. Many sump pumps plug into a GFCI-protected outlet; make sure it has not tripped.
- Look in the pit. Remove the cover and check for debris, silt, gravel or anything that could clog the intake or jam the float.
- Pour water in the pit. Slowly fill the pit with a bucket of water until the float rises.
- Confirm it runs. The pump should start, empty the pit and shut off on its own.
- Listen. Grinding, rattling or loud humming can mean a worn motor or a jammed impeller.
- Check the discharge. Go outside and confirm that water is coming out where it should and flowing away from the foundation.
- Check the check valve. After the pump shuts off, water should not drain back into the pit.
Warning Signs of Trouble
- The pump does not turn on when the water rises
- The pump runs constantly, even when there is little water
- The pump turns on and off rapidly, called short cycling
- Unusual noises or vibration
- Visible rust or corrosion on the pump or discharge pipe
- Water stains or dampness around the pit
- The pump is old and you do not know when it was last replaced
Sump pumps do not last forever. If yours is showing its age or any of these signs, plan a replacement before the next stormy season instead of after a failure.
Consider a Battery Backup
Here is the problem: the same storms that send water into your sump pit can also knock out your power. A standard sump pump without electricity cannot run. A battery backup system adds a second pump, or a backup power source, that kicks in when the main pump loses power or cannot keep up.
Backup options
- Battery backup sump pumps. A secondary pump in the same pit powered by a rechargeable battery. It turns on automatically when the water rises above the primary pump’s normal level.
- Combination systems. A primary pump and battery backup pump sold as a matched unit.
- Water-powered backup pumps. Use municipal water pressure to remove water from the pit without electricity. They depend on adequate water pressure and local rules, so check whether this option fits your home.
- Generators. A standby or portable generator can power the main pump during outages, but it requires proper installation and safe operation.
Many battery backup systems include alarms that alert you when the backup is running, when the battery is low or when water is rising too high. Batteries need periodic checks and replacement according to the manufacturer.
Simple Sump Pump Maintenance
- Keep the pit clean. Remove debris and silt that can clog the intake.
- Clean the intake screen on pumps that have one.
- Keep the float free. Make sure the float can move up and down without catching on the pit walls, cords or pipes.
- Cover the pit to keep out debris and for safety, especially with children and pets around.
- Check the discharge line outside. It should not be clogged, crushed or frozen, and it should send water well away from the house.
- Do not plug other appliances into the sump pump circuit if you can avoid it.
Help Your Pump by Managing Water Outside
Your sump pump has to handle less water when you keep surface water away from the foundation. Clean gutters, keep downspout extensions in place so they discharge several feet from the house, and make sure the ground slopes away from the foundation. These steps reduce how hard the pump has to work and extend its life.
What to Do This Week
- Pour water in the pit to confirm the pump runs and shuts off.
- Clean debris from the pit and check that the float moves freely.
- Confirm the discharge line carries water away from the foundation.
- Check the age of your pump and note any warning signs.
- Consider a battery backup if you do not already have one.
AX Home Pro handles repairs, improvements and maintenance for homeowners. Request an estimate to get started.





